Machine Work

Use of the lathe or mill as a general rule is $60.00 per hour. 
Some specific services offered are as follows: 

GENERAL
Jeweling/Machine Turning

Areas less than 5" diameter (bolt, trigger, etc.) $60.00 
Areas between 5"-10" total diameter $80.00 
Areas over 10" total diameter $80.00 plus $14.00 per square inch

HANDGUN (1911 and others)

Cut serrations on slide (with reblue $110.00) (without reblue $55.00
Cut front or rear sight dovetail for sights $50.00 (sight not included)

1911 style autos

Fit Match Bushing to Slide & Barrel $45.00 (parts not included) 
Fit Match Trigger $45.00 
Trigger Job Standard 3.5 lb.Pull - (Series 70) $65.00 (parts included) 
Trigger Job Competition 2 lb.Pull - (Series 70) $85.00 (parts included) 
Trigger Job Standard 3.5 lb.Pull - (Series 80) $80.00 (parts included) 
Trigger Job Competition 2.5 lb.Pull - (Series 80) $100.00 (parts included) 
Drill & Tap for Scope Mount - (Per Hole) $10.00 plus $45.00 bench fee 
Silver Solder Front Sight (requires reblue or cerakote) $120 
Stake in Front Sight $50.00 
Extractor Tuned and Polished $35.00 
Lower and Flare Ejection Port $50.00 
Throat & Polish Feed Ramp $50.00 
Tighten Slide to Frame $90.00

REVOLVER

Recrown/Chamfer Barrel (Step or 79 Deg) $60.00 
Chamfer Cylinder $60.00 
Install Trigger Over Travel Screw $35.00 
Straighten Crane $60.00 
Port Revolver Barrel $100.00 
Drill & Tap for base per hole $10.00 plus $45.00 bench fee

RIFLE

Cut Dovetail in Barrel $55.00 
Drill & Tap Barrel or Receiver for Sights or Scope Base (Per Hole) $10.00 plus $45.00 bench fee 
Install Front Sight Ramp - Sweat-On Type $60.00 Includes sight 
Install Front Sight Ramp - Screw-On Type $40.00 Includes sight 
Install Pre-Threaded & Chambered Barrel to Action $100.00 
Chamber & Fit Barrel to Action - Std. Caliber's $160.00 
Chamber & Fit Barrel to Action - Win. Pre-64 70 $190.00 
Chamber & Fit Barrel to Action - Wildcat Caliber's $270.00 
Turn & True Receiver Face $25.00 
Turn & True Receiver Locking Lugs & Bolt Locking Lugs $70.00 
Lap Locking Lugs to 600 grit polish $55.00 
Crown & Lap Muzzle $50.00 
Thread Muzzle, Contour & Install Muzzle Brake $90.00 
Thread Protector for Muzzle Brake (Contoured to Barrel) $45.00 
Weld on New Bolt Handle $85.00 
Sweat on Bolt Handle $85.00 
Install & Adj. Timney/Canjar/Shilen Trigger $45.00 (not including trigger) 
Install & Adj. Double or Single Set Trigger $60.00 (not including trigger) "Blueprint" trigger-Consists of highly polish all working areas, complete rebuild of trigger assembly, match spring kit, high polish pins and reset engagement angles for best accuracy. 
Standard triggers $100.00 
Complicated triggers $135.00 (Ruger no.1, etc.)

SHOTGUN

Cut, crown and reset bead (New Standard Bead Included) $60.00 
Cut and crown only on single barrels $50.00 
Drill and tap for sight bead (one) $45.00 
Bead install (factory replacement/no drill or tap) $10.00 includes
standard bead 
Lengthen Forcing Cone - (Non-Plated Bore, Per Barrel) $65.00 
Long Forcing Cone - (Plated Bore, Per Barrel) $95.00 
Straighten / Adjust Barrel $60.00 
Polish Chamber / Bore $65.00 
Remove Stuck Choke Tube $45.00 
Install Screw-In Choke - (Winchoke/Truchoke/Remchoke Non-Plated Bores) $120.00 
Make New Hinge Pin $90.00 
Drill & Tap for Front or Mid Rib Bead $45.00 "Blueprint" trigger-Consists of highly polish all working areas, complete rebuild of trigger assembly, match spring kit, high polish pins, reset engagement angles for best accuracy, polish all levers (pump release, etc) Pump action standard triggers $130.00 
Semi-auto triggers $165.00